The frame is made of metal. There is a polyester label on the device. It is impermeable to wear and tear. The label is immune to low and high temperatures. The dimensions of the SMART FIRST aid KIT: length-25 cm; width-14.5 cm; height-5.5 cm. Weight-1470 g. The device has a special fastening system. It can be mounted on a wall. The lead-acid accumulator (1.2 Ah) is the heart of the device. Operating characteristics Turn on the device, a special signal indicates that the device is turned on. The diodes will be tested, the scale of the first-aid kit will be full. The device runs the previous mode (” Health mode” by default). Use the Laser Tag Configurator program to change the settings. In addition, you can change the settings directly on the go. 1. Changing the settings of the SMART FIRST aid kit using the configurator. To run the programming mode open the program, go to the section 2.0 SMART FIRST AID KIT, connect the USB base to your PC, place the USB base near the first aid kit and turn on the kit. In 5-10 seconds the device will go into programming mode, the configurator will show the type of the connected device and the firmware version. If the SMART FIRST aid KIT is already turned on, select “New Game” on the remote control and place the USB base as described above. The following options are available:” Number of sets ” – how many times can the first-aid kit be used before reloading. This parameter is set in the range from 1 to 250. After activating the mod “Health” or “Ammunition”, the scale will be filled, which indicates that the number of sets has become full. The scale becomes thinner as the player uses the sets. When the number of sets has expired, the diode at the top of the device starts flashing, as do the red diodes at the edge of the scale. You can still use the device by clicking “New Game” on the remote control. You can disable the option, which makes the number of sets unlimited. “Hit the Device Mode” – how many times should the player hit the first aid kit to reduce the number of sets to 1. You should shoot at the diode on top of the frame. When hit, the color of the diode changes to white, after which you will hear a special sound. The scale, which indicates the number of sets, becomes thinner. This parameter is set in the range from 1 to 250 and can also be disabled. “Button Hold Time” – the time during which the player should hold down the button to use the first-aid kit. This parameter is set in the range from 1 to 240 seconds. You can disable the option, in this case the device will start working immediately after pressing the button. “Activation time” – indicates the time that indicates the frequency of the device’s work in the” Energy ” mode. This means that the device activates the selected option at a selected time interval. This parameter is set in the range from 1 to 1800 seconds. “Game Mode” – By exiting the programming mode, the device starts in the selected game mode. “Lap duration” – time during which the device is active from the very beginning of the game. At the end of the set time, the programmed number of sets is automatically reset to zero (even if it is unlimited) and the player will not be able to use the device. You need to restart it (select “New Game” from the remote control). “The health mode”. In this mode, four teams can play: – “Intensive care” (restores players’ health points); – “Instant new game”; – “New game delay” (a new game starts with some delay); – “Restoration of health” (heals the injured players). “Ammunition”. In this mode, eight players can play: – “Restore ammunition” (full ammunition recovery, provided that the player’s ammunition is not full); – “Adds 10 (50, 100) rounds” (adds cartridges if the player’s ammunition is not full); – “Adds 1 (2, 5, 10) magazines” (adds the specified number of magazines if the player’s ammunition is not full). “Power mode.”This is a special mode. When activated, the smart first aid kit can perform one of 26 modes: – “Ammunition recovery”; – “Adds 1 (5, 10, 50, 100) health points” (adds health points unless the player has maximum health points; – “Intensive care”; – “Instant new game”; – “Delaying the new game”; – “Restoring health”; – “Stunning the enemy”; – “Disarming the enemy”; – “Rage” (increases the player’s damage ability to 1 point according to the MILES protocol, provided that the player’s damage level is less than 100);- “Double life until the end of the round”; – ” Achievement 49% (99%)”; – ” Adrenaline 1 (4, 15, 75) points” (restores the player’s health points according to the MILES protocol, provided that the player does not have maximum health); – “Anomaly” (restores 1 health point, provided that the player does not have maximum health); – “Change the team color to red (blue, yellow, green)”; – “Turn Friendly Fire on/off.” 2. 2.0 INTELLIGENT FIRST aid KIT programming on the playground Here you can only change the game mode and limit the number of sets. To select a mode, you should hold down the red button and run the “New Game” mode on the remote control. The diodes begin to flash. Their color depends on the type of mode (“Health” – green; “Ammunition” – yellow; “Energy” – red); Press and hold the button for 2 – 3 seconds to confirm your selection. You will hear a short beep – the device will start selecting the number of sets. You can choose two options – a limited supply (you will receive the preset number of sets; by default – 10 sets) – the red diodes will start flashing, or an unlimited supply-the LEDs will constantly change their color (green-yellow-red). Please confirm your choice by pressing and holding the button for 2 or 3 seconds. Then you will hear three short beeps – this means that the device has rebooted and is ready for use. If the” Health “or” Ammunition ” mode is selected with a limited number of sets, the scale is completely filled. The scale becomes thinner when the sets are used or the first aid kit is attacked. When an unlimited number of sets is selected in the modes, the diodes flash in different colors (green – yellow – red). When the player runs the device in “Health” mode and shoots at it, the color of the LED at the top of the device changes to the color of the player. Then the device will be at the mercy of the team of this color. In this case, you will not be able to recapture the device. When the “Energy” mode is selected (regardless of the number of sets), the scale is gradually filled. When the scale becomes full, you will hear a loud beep. The scale is reset. Pressing the button in this case has no effect. Use the configurator to set the time when the scale becomes full, select the type of team and the number of sets. By default, there are 10 sets; the auto-reset period-10 seconds; the type of mode – “Anomaly.” Download Passport Our manager will help you to make a best choice of weapons for your business.
|
|